Есть местный номер. Как сделать гудок после набора 8. Ну и соответсвенно последующий донабор номера.
Как сделать гудок на 8?
Страница: 1
Сообщений 1 страница 11 из 11
Поделиться22010-03-25 13:34:32
Если про второй ответ станции, то где то так:
ADD CNACLD: PFX=K'8, CSA=NTT, RSC=1, MINL=7, MAXL=24, CHSC=0;
ADD PFXPRO: PFX=K'8, CSC=0, STF=DSDT, TST=1, TT=ST3;
Поделиться32010-03-25 13:43:23
Точно - пока искал mib2005 дал правильный ответ)))
Поделиться42010-04-01 08:00:14
Не гудит. Набираю 8 и тишина после:
%LST CNACLD: PFX="8";%%
RETCODE = 0 Operation succeeded
Call prefix service attribute
-----------------------------
DnSet = 0
Call prefix = 8
Service category = Basic service
Service attribute = National toll
Minimum number length = 11
Maximum number length = 11
Custom attribute = NO
Route selection = 0
Priority selection code = None
Release mode = Unilateral release
Supplementary signaling flag = TRUE
Number initial processing = TRUE
Caller number analysis flag = FALSE
Emergency call observation flag = FALSE
Query area code = FALSE
Free flag = FALSE
Gain = Local gain
Ring delay time = 0
Charging selection = 0
Service sequence number = 0
Time delay trigger point/Special change trigger length = 0
Triggering delay = 0
Destination = 65535
NP query start length = 0
Polarity reversal flag = FALSE
Send calling name = FALSE
Special number change = FALSE
Lawful interception service flag = FALSE
RCSS enable flag = FALSE
INNet Query Flag = FALSE
ACD group = 255
Destination DnSet = 255
Saudi conference list number = 255
INNet office direction = 65535
Standard SSP prefix = TRUE
Long conversation alarm index = 255
%%LST PFXPRO: PFX=K'8;%%
RETCODE = 0 Operation succeeded
DnSet Call prefix
0 8
Special processing attr
-----------------------
Call source = 0
Address nature = National number
Called number change flag = FALSE
Called number change index = No change
Caller number change flag = FALSE
Caller number change index = No change
Fail cause code = Supplementary service activation conflicted
Fail process = FALSE
Re-analyze = FALSE
New DnSet = 0
Send tone = Sending tone between numbers
Signal tone site = 1
Tone type = Dial tone
Поделиться52010-04-01 09:47:26
Поменяй в CNACLD Minimum number length = 11 на Minimum number length = 1
Префикс ОБЯЗАТЕЛЬНО должен быть минимум одна цифра.
Я как то упустил этот момент в сообщении mib2005
Отредактировано james (2010-04-01 09:48:17)
Поделиться62010-04-01 11:32:18
Нет. Не то. Поднимаю трубку все окей. Набираю 8 и тишина, ждет следующих цифр.
Не гудит.
Поделиться72010-04-01 12:10:05
Так длинну на CNACLD поменяли?
У нас работает:
Код:
%%LST CNACLD: PFX="8";%%
RETCODE = 0 Operation succeeded
Call prefix service attribute
-----------------------------
DnSet = 0
Call prefix = 8
Service category = Basic service
Service attribute = National toll
Minimum number length = 1
Maximum number length = 11
Custom attribute = NO
Route selection = 2
Priority selection code = None
Release mode = First party release
Supplementary signaling flag = TRUE
Number initial processing = FALSE
Caller number analysis flag = FALSE
Emergency call observation flag = FALSE
Query area code = FALSE
Free flag = FALSE
Gain = Local gain
Ring delay time = 0
Charging selection = None
Service sequence number = 0
Time delay trigger point/Special change trigger length = 0
Triggering delay = 0
Destination = 65535
NP query start length = 0
Polarity reversal flag = FALSE
Send calling name = FALSE
Special number change = FALSE
Lawful interception service flag = FALSE
RCSS enable flag = FALSE
INNet Query Flag = FALSE
ACD group = 255
Destination DnSet = 255
Saudi conference list number = 255
INNet office direction = 65535
Standard SSP prefix = TRUE
Long conversation alarm index = 255
--- END
%%LST PFXPRO: PFX=K'8;%%
RETCODE = 0 Operation succeeded
DnSet Call prefix
0 8
Special processing attr
-----------------------
Call source = 0
Address nature = All number
Called number change flag = FALSE
Called number change index = No change
Caller number change flag = FALSE
Caller number change index = No change
Fail cause code = Supplementary service activation conflicted
Fail process = FALSE
Re-analyze = FALSE
New DnSet = 0
Send tone = Sending tone between numbers
Signal tone site = 1
Tone type = Dial toneОтредактировано james (2010-04-01 12:19:19)
Поделиться82010-04-01 12:31:31
Прошу прощения, там действительно должно MINL=1 
Поделиться92010-04-01 13:20:31
Все тоже самое, только Release mode = Unilateral release
Покажи номер LST ST со всеми аттрибутами
Поделиться102010-04-01 13:26:29
Вячеслав написал(а):
Все тоже самое
Не все тоже самое - вот где проблема:
%%LST PFXPRO: PFX=K'8;%%
RETCODE = 0 Operation succeededDnSet Call prefix
0 8
Special processing attr
-----------------------
Call source = 0
Address nature = National number
Called number change flag = FALSE
Called number change index = No change
Caller number change flag = FALSE
Caller number change index = No change
Fail cause code = Supplementary service activation conflicted
Fail process = FALSE
Re-analyze = FALSE
New DnSet = 0
Send tone = Sending tone between numbers
Signal tone site = 1
Tone type = Dial tone
А должно быть All number - то есть для всех.
Поделиться112010-04-01 13:26:53
Извините 
Все верно. У меня номер для отдельных категорий был с другим call course. Все работатет.
Страница: 1